Cutting systems

Our high quality shears are often integrated with upstream or downstream machines to a fully automated production line. The machines are custom designed and all the wishes of the customer are respected in the manufacturing of the shear. The drive unit is designed to user specifications and can be realized either hydraulic or as an direct drive with a three-phase gear motor or servo- gear motor or a drive unit with a fly wheel and clutch-break-unit.

HSK/L/Pn 1260 x 1 mm

  • cycle time approx. 2 s
  • cutting angle 2,5°
  • opening 30 mm

Features

  • pneumatic drive
  • very compact design for use
    as flying shear
  • suitable for use in food industry,
    as without lubrication and
    stainless steel on all surfaces

HSK/L 680 x 1,5 mm

  • cycle time approx. 0,6 s
  • cutting angle 1,4°
  • opening 15 mm

Features

  • pneumatic hold down
  • special table for positioning
    of sheet by robot with rotary plate
  • slots for robot gripper
    in the table and hold down

HSK/L 1030 x 1,5 mm

  • cycle time approx. 1,1 s
  • cutting angle 1,47°
  • opening 40 mm

Features

  • shear mounted on
    guideways for manually
    relocating on base frame
  • gravity chute with knobbed
    stainless steel
  • pecial table with space for feeder
  • automatic central
    oil lubrication

HSK/L 1280 x 1,3 mm

  • cycle time approx. 1,1 s
  • cutting angle 1,41°
  • opening 15 mm

Features

  • „vertical fall-down version“
    for stacking in the shear
  • drive mounted at the top
  • manual oil central lubrication

HSK/L/SF 1280 x 1,5 mm

  • cycle time approx. 1,4 s
  • cutting angle 1,2°
  • opening 20 mm

Features

  • cut gap adjustment by levers
    and locking bolts operable
    from one side
  • table permanently clamped
    with disc springs
  • table covered with plastic

HSK/L 1330 x 1,0 mm

  • cycle time approx. 0,84 s
  • cutting angle 1,15°
  • opening 40 mm

Features

  • strip feeder with hydraulic
    motor at the front side
  • steel roll at the back side
  • manual oil central lubrication

HSK/L 1530 x 1,3 mm

  • cycle time approx. 1,1 s
  • cutting angle 1,0°
  • opening 40 mm

Features

  • automatic central
    oil lubrication
  • cut gap adjustment by levers
    and locking bolts
  • welded sidewise base frames
    (width 500 mm)

HSK/L 1530 x 1 mm

  • cycle time approx. 0,8 s
  • cutting angle 1,0°
  • opening 40 mm

Features

  • hold down mounted close
    to the blades
  • manual oil central lubrication
  • blade protection rolls
    in front and behind the table
  • inductive proximity switch
    mounted on the main shaft

HSK/G 630 x 1,25 mm

  • cylce time approx. 1,2 s
  • cutting angle 1,0°
  • opening 76 mm

Features

  • pneumatic hold down
  • sidewise guidances
  • pneumatically actuated back stop
  • automatic sequences

Watch video

HSK/G 680 x 3,25 mm

  • cycle time approx. 1,4 s
  • cutting angle 2,2°
  • opening 20 mm

Features

  • manual oil central lubrication
  • hold down mounted close
    to the blades
  • blade protection roll
    in front of the table

HSK/G 1130 x 2 mm

  • cycle time approx. 1 s
  • cutting angle 1,6°
  • opening 15 mm

Features

  • shear table covered with
    plastic plate
  • manual oil central lubrication
  • hold down mounted close
    to the blades
  • with labels

HSK/G 1280 x 1 mm

  • cycle time approx. 0,8 s
  • cutting angle 1,63°
  • opening 10 mm

Features

  • extra small and
    low construction
  • with own contactor control
  • automatic oil central lubrication
    with time control

HSK/G 1130 x 2 mm

  • cycle time approx. 1,3 s
  • cutting angle 2°
  • opening 22 mm

Features

  • „vertical fall down“-version
  • shear 150mm broadened
  • with control for set up and
    automatic operation
  • robust welded base frame

HSK/G 1330 x 1,6 mm

  • cycle time approx. 0,9 s
  • cutting angle 1,15°
  • opening 20 mm

Features

  • cut gap adjustment by levers
    and locking bolts operable
    from one side
  • table permanently clamped
    with disc springs
  • roller rails in table

HSK/G 1680 x 0,5 mm

  • cycle time approx. 0,75 s
  • cutting angle 0,6°
  • opening 69 mm

Features

  • optimised for continous
    operation by converter
  • broadened for pivoting
    operation
  • special table with
    plastic plates ands brushes
  • without hold down

HSK/G 1830 x 1,2 mm

  • cycle time approx. 1,0 s
  • cutting angle 1,76°
  • opening 30 mm

Features

  • to move material
    lengthwise, base frames manu-
    factured with slots, pivot points
    at the cutter bar relocated
    and motor tilted
  • shear table with ball casters
  • Video ansehen

HSK/G 2530 x 1 mm

  • cycle time approx. 1,2 s
  • cutting angle 1,6°
  • opening 16 mm

Features

  • to move material
    lengthwise, base frames manu-
    factured with slots, pivot points
    at the cutter bar relocated
    and motor tilted
  • table with space for feeder
  • machines mirrored

HSK/W 530 x 1,5 mm

  • cycle time approx. 0,8 s
  • cutting angle 0,52°
  • opening 18 mm

Features

  • shear table covered with
    a brass panel
  • pneumatic hold down
  • manual oil central lubrication

HSK/W 680 x 2 mm

  • cycle time approx. 0,9 s
  • cutting angle 1,47°
  • opening 15 mm

Features

  • electric clutch-brake-unit
  • automatic oil centralised
    lubrication
  • table covered with plastics
    and brushes
  • cut gap adjustment by levers
    and locking bolts

HSK/Wv 630 x 3,5 mm

  • cycle time approx. 0,8 s
  • cutting angle 1,41°
  • opening 8 mm

Features

  • pneumatic clutch
  • table with plastics and
    integrated rolls
  • „vertical fall down“-version
    with opened base frame to pull
    machine out of the production line

HSK/W 1030 x 2,75 mm

  • cycle time approx. 0,9 s
  • cutting angle 1,75°
  • opening 15 mm

Features

  • „vertical fall down“-version
  • manual oil central lubrication

HSK/W 1330 x 1,75 mm

  • cycle time approx. 0,8 s
  • cutting angle 1°
  • opening 20 mm

Features

  • hold down mounted close
    to the blades
  • manual oil central lubrication

HSK/W 1530 x 1 mm

  • cycle time approx. 0,8 s
  • cutting angle 0,52°
  • opening 18 mm

Features

  • shear table covered with
    plastic plate
  • pneumatic hold down
  • manual oil central lubrication

HSK/W 1680 x 1,5 mm

  • cycle time approx. 0,8 s
  • cutting angle 1,58°
  • opening 20 mm

Features

  • extra wide table covered
    with plastic
  • table and hold down
    prepared for pliers feed
  •  cam switch mounted
    on the side

HSK/N 220 x 4 mm

  • cylce time approx. 0,25 s
  • cutting angle 1,9°
  • opening 25 mm

Features

  • very high number of strokes
    via direct drive
  • top – drive
  • without holddown
  • table covered with stainless steel
  • with base frame and
    vibration-damping-wedge shoes

HSK/N 430 x 3 mm

  • cycle time approx. 0,3 s
  • cutting angle 2,16°
  • opening 15 mm

Features

  • very high number of strokes
  • lateral band feed
  • foldable transfer table
    on the back side of the machine

HSK/N 630 x 2,5 mm

  • cylce time approx. 0,45 s
  • cutting angle 1,5°
  • opening 15 mm

Features

  • very high number of strokes
    via direct drive
  • table covered with plastics
    and brushes
  • automatic oil centralised
    lubrication

HSK/N 1030 x 2 mm

  • cycle time approx. 1,2 s
  • cutting angle 1,7°
  • opening 78 mm

Features

  • table covered
    with plastic and brushes
  • pneumatic hold down
  • prepared to install
    a rotary encoder
  • automatic central
    oil lubrication

HSK/N 1030 x 2,75 mm

  • cycle time approx. 0,7 s
  • cutting angle 1,75°
  • opening 15 mm

Features

  • table covered with plastics
    and brushes
    table and on cutterbar
  • cut gap adjustment by levers
    and locking bolts
  • shear table claped with springs
  • automatic oil centralised
    lubrication

HSK/N/SF 1280 x 2,5 mm

  • cycle time approx. 0,7 s
  • cutting angle 2,1°
  • opening 20 mm

Features

  • „vertical fall down“-version
  • plastic casters integrated in table
  • opened base frame
  • integrated srap gate
  • automatic central
    oil lubrication

HSK/N 1280 x 3 mm

  • cycle time approx. 0,9 s
  • cutting angle 2,1°
  • opening 40 mm

Features

  • blade protection roll
    mounted in front of the
    table and on cutterbar
  • exchangable frame and
    crane lifting hooks
  • manual oil central lubrication

HSK/N 1280 x 2,5 mm

  • cycle time approx. 0,7 s
  • cutting angle 1,2°
  • opening 20 mm

Features

  • shear mounted on
    swivel unit
  • able to cut 10 mm fleece material
  • automatic central
    oil lubrication

HSK/N 1330 x 2,5 mm

  • cycle time approx. 0,85 s
  • cutting angle 1,78°
  • opening 25 mm

Features

  • cut gap adjustment by levers
    and locking bolts operable
    from one side
  • automatic central
    oil lubrication
  • welded base frame
  • with own control

HSK/N 1330 x 3 mm

  • cycle time approx. 0,9 s
  • cutting angle 2°
  • opening 20 mm

Features

  • table covered with plastics
    and brushes
  • automatic oil centralised
    lubrication
  • pneumatic hold down

HSK/N 1380 x 2,75 mm

  • cutting time approx. 0,8 s
  • cutting angle 1,5°
  • opening 30 mm

Features

  • Shear cuts within a distance
    of 310 mm
  • motor driven base frame
  • automatic central oil lubrication
  • press safety valve
  • prepared for mounting to an
    energy chain

HSK/N/SF 1530 x 3,3 mm

  • cycle time approx. 1,3 s
  • cutting angle 1,9°
  • opening 16 mm

Features

  • „vertical fall down“-version
  • shear table covered with
    plastic plate
  • welded base frame
  • manual oil central lubrication

HSK/N 1630 x 2,5 mm

  • cycle time approx. 1,2 s
  • cutting angle 1,8°
  • opening 15 mm

Features

  • shear table covered with
    plastic plate
  • manual oil central lubrication
  • hold down mounted close
    to the blades

HSK/N/SF 1680 x 3 mm

  • cycle time approx. 0,8 s
  • cutting angle 0,91°
  • opening 40 mm

Features

  • flexible blade protection
    casters in the table
  • special table with space
    for feeder
  • table covered with
    plastics and brushes
  • manual oil central lubrication

HSK/N 2030 x 1,5 mm

  • cycle time approx. 0,9 s
  • cutting angle 1,59°
  • opening 30mm

Features

  • douple cut via top drive
  • sidways consoles for travel rails
  • pneumatic scrap gate
  • shear table coverd with
    stainless steel

HSK/N 2230 x 2,5 mm

  • cycle time approx. 1,1 s
  • cutting angle 2°
  • opening 28 mm

Features

  • table with space for feeder
  • rotary encoder installed
  • manual oil central lubrication
  • press-safety-valve premountedli>

HSK/N 2330 x 80 mm Foam

  • cycle time approx. 0,9 s
  • cutting angle 1,0°
  • opening 105 mm

Features

  • motor driven feed roll,
    lower roll coverd with silicone
  • measuring system included
  • automatic central oil lubrication
  • press safety valve

HSK/N 2380 x 2,5 mm Foam

  • cycle time approx. 1,4 s
  • cutting angle 1,6°
  • opening 80 mm

Features

  • pneumatic hold down
  • cross beams higher placed than
    normal to use as flying shear
  • able to cut 10mm fleece material
  • manual oil central lubrication

HSK/N 3530 x 1,5 mm

  • cycle time approx. 1,4 s
  • cutting angle 1,5°
  • opening 15 mm

Features

  • table with space for feeder
  • manual oil central lubrication
  • hold down mounted close
    to the blades

HSK/S 630 x 3,5 mm

  • cycle time approx. 0,8 s
  • cutting angle 1,5°
  • opening 15 mm

Features

  • special design for cutting
    upwards
  • special sidframes for easier
    removal of material
  • table covered with plastics
    and brushes
  • holddown integrated in cutterbar

HSK/S 630 x 4 mm

  • cycle time approx. 1,8 s
  • cutting angle 1,7°
  • opening approx. 45 mm

Features

  • special C-shaped
    construction with upper drive
  • with contactor control
    and two-hand operation
  • motor-driven base frame

HSK/S/SF 630 x 5 mm

  • cycle time approx. 1,0 s
  • cutting angle 1,5°
  • opening 22 mm

Features

  • drive unit mounted comletly
    on one side
  • cut gap adjustment by levers
    and locking bolts
  • “vertical fall down”-version
    with opened base frame to take
    out sample material

HSK/S 730 x 6 mm

  • cycle time approx. 2,2 s
  • cutting angle 3,2°
  • opening 15 mm

Features

  • completely encased
    guillotine shear
  • shear table in special design
  • welded base frame with slots
    for forklift
  • automatic oil central lubrication
    with time control

HSK/S 830 x 10 mm

  • cycle time approx. 0,65 s
  • cutting angle 3,0°
  • opening 30 mm

Features

  • special table with space
    for feeder
  • automatic central
    oil lubrication
  • hydraulically operated clutch

HSK/S 1030 x 4,0 mm

  • cycle time approx. 1,45 s
  • cutting angle 2,6°
  • opening 40 mm

Features

  • special table with space
    for feeder
  • without hold down
  • cut gap adjustment by levers
    and locking bolts
  • manual oil central lubrication

HSK/S 1030 x 6 mm

  • cycle time approx. 1 s
  • cutting angle 2°
  • opening 50 mm

Features

  • without hold down
  • automatic central
    oil lubrication
  • cut gap adjustment by levers
    and locking bolts
  • Press-safety-valve

HSK/S 1030 x 6 mm

  • cycle time approx. 0,7s
  • cutting angle 1,75°
  • opening 15 mm

Features

  • automatic cut gap
    adjustement with motors and
    hydraulic clamping
  • hold down close to the cut
    and with vulkollan and
    guiding wedge
  • special table with space for feeder

HSK/S 1130 x 4,5 mm

  • cycle time approx. 1,6 s
  • cutting angle 1,6°
  • opening 14 mm

Features

  • pneumatic hold down
  • hold down broadened
    for two rubber cords
  • special welded base frame
    to achive a coil pass height
    of 1200 mm

HSK/S 1680 x 4,5 mm

  • cycle time approx. 0,6 s
  • cutting angle 1,58°
  • opening 20 mm

Features

  • ridig guiding wedge
    insted of hold down
  • special table with
    space for rubberized rollers
  • automatic central oil lubrication

HSK/S 1930 x 2 mm

  • cycle time approx. 0,9 s
  • cutting angle 2,1°
  • opening 36 mm

Features

  • table coverd with
    plastic and brushes
  • hold down close to the
    cut with guiding wedge
  • automatic central oil lubrication

HSK/S 2030 x 4 mm

  • cycle time approx. 1,0 s
  • cutting angle 1,45°
  • opening 30 mm

Features

  • hydraulic clutch-brake
    combination
  • press safety block
  • special table with space for feeder
  • cam switch or
    rotary encoder installed

HSK/S 2030 x 5 mm

  • cycle time approx. 3,5 s
  • cutting angle 1,8°
  • opening 40 mm

Features

  • special table with
    space for feeder
  • shear is inclined mounted
    on motor driven base frame
  • hold down close to the cut

HSK/Sv/SF 2030 x 6 mm

  • cycle time approx. 1,2 s
  • cutting angle 1,6°
  • opening 20 mm

Features

  • cut gap adjustment by levers
    and locking bolts
  • flexible casters in the table
  • table covered with
    plastics and brushes

HSK/Sv 2030 x 7 mm

  • cycle time approx. 1,0 s
  • cutting angle 1,7°
  • opening 15 mm

Features

  • motor driven cut gap
    adjustement
  • special welded stands
    to achive a lower coil pass height
  • hold down close to the cut
  • table permanently clamped
    with disc springs

HSK/S 2130 x 4,5

  • cycle time approx. 0,9 s
  • cutting angle 1,67°
  • opening 50 mm

Features

  • pneumatic holddown
  • special table covered with
    plastics and brushes
  • special feeding wedge infront
    of the holdhown
  • suitable for 10 mm fleece material

HSK/S 2130 x 5 mm

  • cycle time approx. 0,9 s
  • cutting angle 2,0°
  • opening 36 mm

Features

  • prepared for mounting to an
    energy chain and conveyor belt
  • horizontal sheet metal support
    on the back side of the machine

HSK/S 2230 x 4 mm

  • cycle time approx. 0,7 s
  • cutting angle 1,7°
  • opening 180 mm

Features

  • bi-servo-drive
  • automatic cut gap
    adjustement with motors and
    hydraulic clamping
  • motor driven blade
    protection rolls

see video

HSK/S 2230 x 5,5 mm

  • cycle time approx. 1,0 s
  • cutting angle 1,75°
  • opening 23 mm

Features

  • special table with space
    for feeder
  • cam switch
  • special press safety valve
  • central oil lubrication
    with progressive distributor

HSK/S 2230 x 5 mm

  • cycle time approx. 0,75 s
  • cutting angle 1,7°
  • opening 50 mm

Features

  • centered servo-drive
  • automatic cut gap
    adjustement with motors and
    hydraulic clamping
  • motor driven blade
    protection rolls

Video ansehen

HSK/S 3280 x 6 mm

  • cycle time approx. 1,2 s
  • cutting angle 1,61°
  • opening 20 mm

Features

  • table covered with
    stainless steel
  • 3 windows in the hold down
  • manual oil central lubrication
  • hold down with vulkollan

HSK/S 4030 x 3 mm

  • cycle time approx. 1,7 s
  • cutting angle 1,9°
  • opening 25 mm

Features

  • special table with
    space for feeder
  • cut gap adjustment by levers
    and locking bolts
  • automatic central oil lubrication

HSK/S/Hy 1280 x 8 mm

  • cycle time approx.1,5s at 370 l/min.
  • cutting angle 2,5°
  • opening 90 mm

Features

  • ridig guiding wedge
    infront of the hold down
  • scrap chute behind the machine
  • automatic central oil lubrication

HSK/S/Hy 1630 x 3 mm

  • cycle time: dependent on
    hydraulic power unit
  • cutting angle 2,6°
  • opening 120 mm

Features

  • Cutter bar manufactured
    extra slim, in order to folt up the
    transfer table behind the machine.
  • manual oil central lubrication

HSK/S/Hy 1680 x 5 mm

  • cycle time: dependent on
    hydraulic power unit
  • cutting angle 2,5°
  • opening 175 mm

Features

  • blade protection roll
    mounted on cutter bar
  • extra spring actuated
    blade protection roll
    integrated in the table
  • manual oil central lubrication

HSK/S/Hy 2130 x 12 mm

  • cycle time: dependent on
    hydraulic power unit
  • cutting angle 2,2°
  • opening 60 mm

Features

  • automatic cut gap
    adjustement with motors and
    hydraulic clamping
  • blade protection roll
    in front of the table
    and below the cutter bar
  • automatic central oil lubrication

HSK/S/Hy 3530 x 15 PVC mm

  • cycle time: dependent on
    hydraulic power unit
  • cutting angle 2,5°
  • opening 100 mm

Features

  • special table with
    space for feeder
  • extra big opening of
    cutterbar and hold down
  • manual oil central lubrication

Application areas

The machines are mainly used in cut-to-length and press lines for preparing the metal strip, cut-to-length and for processing the end of the strip. Often metal sheets are fed automatically to trim them or divide them for further processes. Not only in lines to process sheet metal also shears are used in production lines for plastic, CFRP/GFRP, fleece material and foam.

Standard equipment

  • Vibration damped grey cast iron stands
  • Robust welded shear table with flat support surface
  • Spring actuated hold-down manufactured out of one piece with glued-in rubber cord
  • One-piece steel blades out of special blade steel with four cutting edges with 90 degree wedge angle
  • Manually actuated oil lubrication
  • Oil drip pans with oil drain screws under the main bearings and eccentric
  • Cut gap adjustment by fine threaded spindles
  • special painting on demand